The printer is an essential PC peripherals. Most printers use a PC or a Centronics parallel interface.
On the PC, the interface is a female connector 25 pin D type, parallel interface is sending eight bits of data simultaneously, where the channel strobe tells the printer when there are characters to read.
For parallel interface readings decreased, then the printer reads the data byte, then the acknowledge signal is used to notify the computer that the interface is ready to grow again. Another signal is used to inform the PC when the interface is active or busy, an error has occurred or out of paper and others. The printer, like any other proposition, will be profitable if treated carefully. In most printers, the cleaning is done setiapmengganti ribbon is too often.
To clean the printer, first turn off the printer, unplug the electrical current from the plug socket and then remove the lid. For laser printers, follow established procedures in the manual on cleaning and replacing the cartridge.
For laser jet printers that use Canon type, then you need to do is clean the corona wire carefully to move the toner reservoir. For this you have to replace it every three or four times a replacement cartridge. But it's good, when the printer is open, to check the machine and be careful throwing dirt, toner or paper dust menumnup in it. As for the type of dot-matrix printer or inkjet printer, then you need to do is remove the tape or ink cartridges, then watch how the tape moves past the 'head' print.
Thus you can replace it later, the next step is to carefully hapulah paper dust that has fallen into the machine. Then check that no piece of paper or adhesive label paper that blocked her way. For a thinner card is usually used to clean the dirt.
Clean 'Head' Print
Another thing you need to consider, that if you can clean the 'head' dot-matrix print or daisywheel wear special facilities, such as those produced by Perfect Data.
Facility consists of a sheet of cleaning that is inserted through a printer that seemed to be paper and cleaning solution. So you need to do is wet the sheet with a solution, then run the printer to print on it (without a ribbon) while for the test. Where the solution was to dissolve the remnants of the ink is dry, then absorbed by the sheet.
Or you can do another way by using a special cleaning cartridge is inserted as a replacement. In addition you also need to clean the platen (a rubber cylinder) to remove the remaining ink when the paper was printed.
Perfect Data is a special cleaner with brush molds, where it is useful to clean the platen to get ink. But the pads that protect the solution can also be used to clean the exterior of the platen.
If any part of the printer is not able to move freely, then put on the engine lubricating oil (with notes refer to the user guide for the printer you use). Most printers use bearings that are designed to not require lubrication.
If dirt or dust had soiled paper, then a drop of oil is needed to clean it. If you need a lubricant, it is advisable to use minimum. After you finish cleaning it then attach a ribbon or a new ink cartridge. Take the test to check the printer, so printing quality control provisions memuaskan.Kebanyakan printers have the distance between the print head and platen.
To minimize wear and tear then work out how to set up a space that gives the maximum print quality bagus.Dari above activities then close the printer clean using a soft cloth and detergent solution and then put back.
Place the paper in the tray or insert paper carefully (do not coercion), then make sure the paper go smoothly without involving the lain.Dari steps above the bottom line is:
1. Turn off the printer, remove the lid and ribbon.
2. Clean dust or dirt on the printer.
3. Check and clean the streets and out of the paper and platen.
4. Clean and replace the 'head' print.
5. Replace the ribbon if it has run out.
6. Do a test print to get a satisfactory print quality.
7. Clean and return the printer cover.
8. Make checks and make sure paper is installed correctly and smoothly entry conditions
On the PC, the interface is a female connector 25 pin D type, parallel interface is sending eight bits of data simultaneously, where the channel strobe tells the printer when there are characters to read.
For parallel interface readings decreased, then the printer reads the data byte, then the acknowledge signal is used to notify the computer that the interface is ready to grow again. Another signal is used to inform the PC when the interface is active or busy, an error has occurred or out of paper and others. The printer, like any other proposition, will be profitable if treated carefully. In most printers, the cleaning is done setiapmengganti ribbon is too often.
To clean the printer, first turn off the printer, unplug the electrical current from the plug socket and then remove the lid. For laser printers, follow established procedures in the manual on cleaning and replacing the cartridge.
For laser jet printers that use Canon type, then you need to do is clean the corona wire carefully to move the toner reservoir. For this you have to replace it every three or four times a replacement cartridge. But it's good, when the printer is open, to check the machine and be careful throwing dirt, toner or paper dust menumnup in it. As for the type of dot-matrix printer or inkjet printer, then you need to do is remove the tape or ink cartridges, then watch how the tape moves past the 'head' print.
Thus you can replace it later, the next step is to carefully hapulah paper dust that has fallen into the machine. Then check that no piece of paper or adhesive label paper that blocked her way. For a thinner card is usually used to clean the dirt.
Clean 'Head' Print
Another thing you need to consider, that if you can clean the 'head' dot-matrix print or daisywheel wear special facilities, such as those produced by Perfect Data.
Facility consists of a sheet of cleaning that is inserted through a printer that seemed to be paper and cleaning solution. So you need to do is wet the sheet with a solution, then run the printer to print on it (without a ribbon) while for the test. Where the solution was to dissolve the remnants of the ink is dry, then absorbed by the sheet.
Or you can do another way by using a special cleaning cartridge is inserted as a replacement. In addition you also need to clean the platen (a rubber cylinder) to remove the remaining ink when the paper was printed.
Perfect Data is a special cleaner with brush molds, where it is useful to clean the platen to get ink. But the pads that protect the solution can also be used to clean the exterior of the platen.
If any part of the printer is not able to move freely, then put on the engine lubricating oil (with notes refer to the user guide for the printer you use). Most printers use bearings that are designed to not require lubrication.
If dirt or dust had soiled paper, then a drop of oil is needed to clean it. If you need a lubricant, it is advisable to use minimum. After you finish cleaning it then attach a ribbon or a new ink cartridge. Take the test to check the printer, so printing quality control provisions memuaskan.Kebanyakan printers have the distance between the print head and platen.
To minimize wear and tear then work out how to set up a space that gives the maximum print quality bagus.Dari above activities then close the printer clean using a soft cloth and detergent solution and then put back.
Place the paper in the tray or insert paper carefully (do not coercion), then make sure the paper go smoothly without involving the lain.Dari steps above the bottom line is:
1. Turn off the printer, remove the lid and ribbon.
2. Clean dust or dirt on the printer.
3. Check and clean the streets and out of the paper and platen.
4. Clean and replace the 'head' print.
5. Replace the ribbon if it has run out.
6. Do a test print to get a satisfactory print quality.
7. Clean and return the printer cover.
8. Make checks and make sure paper is installed correctly and smoothly entry conditions
0 comments: on "Printer Care Tips"
Post a Comment