Tuesday, September 20, 2011

Printer Care Tips To More Autos




















If not treated, the printer could be 'cranky' and the performance becomes optimal. For this reason, the printer also needs to be treated like other electronic devices in order to remain in good condition. Here are some tips on how to maintain the printer is easy and inexpensive, and borne, the printer you are healthy and able to work more optimally. 

Use the Periodic Printer To prevent poor print quality, use your printer periodically at least 2-3 times a week. This will make the flow of ink from the hole remains smooth. If you include rarely use the printer, maybe you need a piece of paper to remind you to print with color or black and white ink at least 2 times a week to maintain the smooth flow of ink. 

Turn off the printer If Not Used Do not forget to always turn off the printer when not in use. This will prevent the closing holes of the flow of ink in the printer head. 

Clean Dirt in Printers Clean the inside of the printer every one or two weeks, depending on how often and how much you use the printer. This will keep your printer in the printing capabilities. Do not forget to observe whether there are objects left in the printer such as paper clips and so on. Do not store the printer in a dusty or full of insects. If it is a dusty place, it's good printer with plastic wrap to protect it from dirt. 

Keep Good When Replacing Cartridge with Ink Printer cartridges full of delicate electronic interface. These objects may be damaged if treated carelessly. Could be the signal to the computer to be broken or poor prints. Therefore, treat the cartridge carefully. 

Use Diagnostic Tools The whole printer has the software's help on how to care for or overcome the problem of the printer. Take time to learn. Perhaps the information provided can help you overcome problems in your printer. 

Turn off the printer If Failed Printing Failure to print or error message that sometimes appears, sometimes can be overcome by turning off the printer, then unplug the power cord for at least ten minutes. After that, insert the power cord at the plug, turn on the printer and try printing again. This way is often able to overcome the failure to print properly.

read more...

Printer Care Tips

 

The printer is an essential PC peripherals. Most printers use a PC or a Centronics parallel interface.
On the PC, the interface is a female connector 25 pin D type, parallel interface is sending eight bits of data simultaneously, where the channel strobe tells the printer when there are characters to read.
For parallel interface readings decreased, then the printer reads the data byte, then the acknowledge signal is used to notify the computer that the interface is ready to grow again. Another signal is used to inform the PC when the interface is active or busy, an error has occurred or out of paper and others. The printer, like any other proposition, will be profitable if treated carefully. In most printers, the cleaning is done setiapmengganti ribbon is too often.
To clean the printer, first turn off the printer, unplug the electrical current from the plug socket and then remove the lid. For laser printers, follow established procedures in the manual on cleaning and replacing the cartridge.
For laser jet printers that use Canon type, then you need to do is clean the corona wire carefully to move the toner reservoir. For this you have to replace it every three or four times a replacement cartridge. But it's good, when the printer is open, to check the machine and be careful throwing dirt, toner or paper dust menumnup in it. As for the type of dot-matrix printer or inkjet printer, then you need to do is remove the tape or ink cartridges, then watch how the tape moves past the 'head' print.
Thus you can replace it later, the next step is to carefully hapulah paper dust that has fallen into the machine. Then check that no piece of paper or adhesive label paper that blocked her way. For a thinner card is usually used to clean the dirt.
Clean 'Head' Print
Another thing you need to consider, that if you can clean the 'head' dot-matrix print or daisywheel wear special facilities, such as those produced by Perfect Data.
Facility consists of a sheet of cleaning that is inserted through a printer that seemed to be paper and cleaning solution. So you need to do is wet the sheet with a solution, then run the printer to print on it (without a ribbon) while for the test. Where the solution was to dissolve the remnants of the ink is dry, then absorbed by the sheet.
Or you can do another way by using a special cleaning cartridge is inserted as a replacement. In addition you also need to clean the platen (a rubber cylinder) to remove the remaining ink when the paper was printed.
Perfect Data is a special cleaner with brush molds, where it is useful to clean the platen to get ink. But the pads that protect the solution can also be used to clean the exterior of the platen.
If any part of the printer is not able to move freely, then put on the engine lubricating oil (with notes refer to the user guide for the printer you use). Most printers use bearings that are designed to not require lubrication.
If dirt or dust had soiled paper, then a drop of oil is needed to clean it. If you need a lubricant, it is advisable to use minimum. After you finish cleaning it then attach a ribbon or a new ink cartridge. Take the test to check the printer, so printing quality control provisions memuaskan.Kebanyakan printers have the distance between the print head and platen.
To minimize wear and tear then work out how to set up a space that gives the maximum print quality bagus.Dari above activities then close the printer clean using a soft cloth and detergent solution and then put back.
Place the paper in the tray or insert paper carefully (do not coercion), then make sure the paper go smoothly without involving the lain.Dari steps above the bottom line is:
1. Turn off the printer, remove the lid and ribbon.
2. Clean dust or dirt on the printer.
3. Check and clean the streets and out of the paper and platen.
4. Clean and replace the 'head' print.
5. Replace the ribbon if it has run out.
6. Do a test print to get a satisfactory print quality.
7. Clean and return the printer cover.
8. Make checks and make sure paper is installed correctly and smoothly entry conditions 
read more...

Thursday, September 8, 2011

Tips Care System and Speed ​​up Computer Work

 



In the daily work with computers, sometimes with a variety of reasons a computer is experiencing a delay or even damage to computer systems so it is very disturbing performance of the computer itself and employees or computer users.

When the computer is experiencing a delay systems work there are several causes
to look out for include:
a. because the virus.
b. Because the hardware device.
c. Care System (software) is lacking.
For maintenance of computer virus attacks can be overcome by installing antivirus free or a paid

In the "maintenance tips computer system", here to note is how the computer when the hardware is ready but still need maintenance on the system or software, especially here on the System Windows XP or Vista. There are a few tips on maintenance as follows:

1. Try using Windows XP or Vista software is genuine, not pirated because the original can always update to the internet, so that any leakage in the system time windows can be closed by way of live updates via the Internet.

2. Anti-virus either free or paid already installed and updated.

3. Clean always rubbish computer system with an automatic aid program rather than manually, the program is small but very nice for taking care system, ie delete internet cookies, delete files used like tanks. and most importantly can remove the remnants of the registry when installing the program baru.bisa also to visit the install program.
 
4. Once completed then Install additional programs to accelerate the speed of hard drives and memory, this small program, but also powerful functions, many menu choices include: clean error, fix error, system speed, disk speed etc.. After Install run the program with 2x click and select the menu that tersedia.Dijamin your computer 300% faster.
read more...

How to Reset Epson TX110 - TX111 printer Using Software























Opportunity this time I'll be posting a way to reset the Epson printer TX110 and TX111. Immediately, how the heck How To Reset Printer Epson TX110 - TX111 is using the software.

How to Resetter Epson TX110 - TX111 Using Software:

Need I remind you before, How the adjustment program is similar to a virus that is usually detected as a virus by the Antivirus. Before running this program I recommend to turn off the Antivirus buddy first so that it goes to work.

     * The first step should have installed the printer driver. To Download the driver Buddy can click here
     * Download software resetter Epson TX110 - TX111 it here
     * Run the program resetter Epson TX110 - TX111 by 2x click the file "AdjProg.exe"
     * Then Buddy follow the steps as shown below:































































































1. Check: used to counter check the maximum 7800 points, my friend can see it in the main pad counter. If more or close to 7800 points means the printer needs to be reset.
2. Initialization: used to reset or restore it to the position of Counter Zero Ink printer "

* When finished turn the printer off then on again. The printer will flame with a full green light. Means the printer is the Epson Stylus TX110 - TX111 that blink had been ready for use again.

  Good luck ............



read more...

How To Overcome Blinking On Epson TX111 Printer

undefined





There may be a Buddy who uses Epson TX111, and there happens to this day I am a new customer to buy a printer Epson TX111 is already in modif. For my friend and new customers who bought this Epson Printer series please scrutiny may be useful later on when the printer is having problems Epson TX111 Blinking  

 Blinking Epson TX111 Service Method:


1. Blink on paper drawings

If blinking on paper means the paper can not enter or commonly called a paper jam. This damage is usually caused by rubber paper loading (for whatever it's called) was already weak or there is something uncomfortable about the way the paper.
- If a lump try to manually turn the paper laid on paper tray.
- If rubber loading paper already weak replace it with a new or semi-circle around the rubber


2. Blink on ink drawings

Ink reset request. The first way of changing the designated catrid problematic, a second way into the printer driver, right click click properties click the printing preferences click catrid replacement ink maintenance click. catrid wait until the position can be removed / taken. then take catrid designated problem or take it all wait a while and then plug it back and forward commands provided in the ink replacement catrid earlier. hopefully've no error anymore


3. Blink on paper and ink drawing

Initially the movement was normal normal printer. but at warmingup scaner suddenly the sound track track track track continues then blink of paper and ink drawing. This occurs because the scanner was weak and was unable to read the sensor so immediately wrote replace with new (price scanernya probably wrote about 300 thousands if not mistaken) or search for a cannibal.

may be useful
read more...

How to Resetter Canon printer MP198 error E27













I was often get questions about how to reset Canon MP198, and this time I want to share about How to Reset Canon MP198 with error E27.



How to Resetter Canon MP198 error E27 : prepare in service mode :

  • The printer is off and plugged the power cord.
  • Press and hold STOP / RESET then press and hold POWER.
  • Release the button STOP / RESET (POWER button should not be released)
  • Press STOP / RESET 2 (two) times, then release the POWER button
  • Let green LED blink until the printer head stops moving. And the LCD panel shows number 0 (zero).
  • The computer will detect new hardware, just ignore it.
  • This situation meaning that Canon MP198 printer is in the SERVICE MODE and ready for reset.
  • Next  Step run MP198 Resetter, if  you don't have it, please download Resetter MP198 at this link http://www.ziddu.com/download/12372220/ServiceTool_V1074MP198.zip.html


 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
How to Resetter Canon MP198 error E27 :
  • Exctract File Resetter MP198.
  • Prepare a second paper in the printer (to print at the time of the reset process)
  • Run the program Resetter MP198.
  • Click "MAIN", the printer will proceed, then MP198 will print one page with the words "D = 000.0 ....."
  • Click the "EEPROM Clear".
  • Then click the "EEPROM", and the printer will print the results of Resetter MP198. One of the writing row as follows : "TPage (COPY TTL = 00 000 = 00 000)"
  • Turn off the printer by pressing the POWER button.
  • Done ...
Good luck.
read more...

How to Reset Canon printer IP2770 Error 5B00














This time I will share about  How to Reset Canon printer  IP2770 Error 5B00. I was try this resetter and runs perfectly. 100% working. This resetter no passwords ... and FREE



How to Reset Canon printer IP2770 Error 5B00


Download Canon iP2770 Resetter v1074 no password below:

http://www.ziddu.com/download/11980752/ServiceTool_V1074_iP2770.rar.html


Do not forget to turn off the download manager, so the iP2770 Resetter successfully downloaded.


Go to the iP2770 Service Mode :


  • The printer is off and plugged the power cord.
  • Press the RESUME button two seconds
  • then press the POWER button until the green light flame (while pressing the POWER button, ... don't release RESUME button)
  • Then release the Resume button, but do not release the POWER button.
  • POWER button while still pressed, press the Resume button 5 times. Led will flash alternately orange glow green with the last orange. (not to mistaken 4x because the printer will be totally dead, but it is temporary as well) Then ...
  • Release both buttons simultaneously.
  • Led will blink briefly and then will glow GREEN.
  • The computer will detect new devices, please ignore .....
  • This situation is called SERVICE MODE iP2770 and iP2770 ready to be reset.




















Then run Canon printer iP2770 Resetter v1074 :
  • Exctract File iP2770 Resetter.
  • Prepare a two paper in the printer (to print at the time of the reset process).
  • Run the program iP2770 Resetter
  • Click "MAIN", then the printer will proceed and iP2770 will print one page with the words "D = 000.0"
  • Click the "EEPROM Clear".
  • Then click the "EEPROM", and the printer will print the results off iP2770 Resetter. One of the writing row as follows:
  • "TPage (TTL = 00 000)"
  • Turn off the printer by pressing the POWER button.
  • Done ...
read more...

How to Resetter Canon printer mp198 error E27












I was often get questions about how to reset Canon printer  MP198, and this time I want to share about How to Reset Canon printer MP198 with error E27.



How to Resetter Canon MP198 error E27 : prepare in service mode :

  • The printer is off and plugged the power cord.
  • Press and hold STOP / RESET then press and hold POWER.
  • Release the button STOP / RESET (POWER button should not be released)
  • Press STOP / RESET 2 (two) times, then release the POWER button
  • Let green LED blink until the printer head stops moving. And the LCD panel shows number 0 (zero).
  • The computer will detect new hardware, just ignore it.
  • This situation meaning that Canon MP198 printer is in the SERVICE MODE and ready for reset.
  • Next  Step run MP198 Resetter, if  you don't have it, please download Resetter MP198 at this link http://www.ziddu.com/download/12372220/ServiceTool_V1074MP198.zip.html











How to Resetter Canon printer MP198 error E27 :
  • Exctract File Resetter canon printer MP198.
  • Prepare a second paper in the printer (to print at the time of the reset process)
  • Run the program Resetter MP198.
  • Click "MAIN", the printer will proceed, then MP198 will print one page with the words "D = 000.0 ....."
  • Click the "EEPROM Clear".
  • Then click the "EEPROM", and the printer will print the results of Resetter canon printer MP198. One of the writing row as follows : "TPage (COPY TTL = 00 000 = 00 000)"
  • Turn off the printer by pressing the POWER button.
  • Done ...
Good luck.
read more...

How to Fix Error B200 on Canon iP2770 and MP258














This time I will share experiences about How to Fix Canon iP2770 and MP258 with Error B200. This question is often asked and I will answer now. This answer is from my friend who want to share about his experience.


How to Fix Error B200 on Canon iP2770 and MP258 :

Here is step by step to fix Error B200 on Canon iP2770 and MP258, but No Result ( Unclear) :

  • Reset Printer with software resetter = unclear.
  • Press Resume button 15 - 25 minutes, print result is not good.
  • Replace the catrid with the new one = result is unclear.
Finally this is the way How to Fix Error B200 on Canon iP2770 and MP258 :

Replace power supply / adaptor on your iP2770 or MP258. And the error B200 on iP2770 and MP258 will soon be resolved.











This picture is just an illustration.

Good luck.
read more...

How to Reset Canon IP2770 with Error 5200










This time, I will try sharing on How to Reset Canon IP2770 Error 5200. IP 2770 is a new printer, and I also at the first time get error 5200 on canon iP2770. Want to know how ...?

Early Indication:
When the iP2770 is turned on, the printer looks normal with GREEN LED on. But when ordered to print, then the 5200 on iP2770 error will appear, and the LED will blinking 8x green 1x orange.

 
 How To Reset Canon IP2770 Error 5200 :

  1. The printer is off and plugged the power cord.
  2. Press the RESUME button two seconds,
  3. then press the POWER button until the green light flame ( while pressing the POWER button, don't released RESUME button )
  4. Then release the Resume button, but do not release the POWER button.
  5. POWER button while still pressed, press the Resume button 5 times. Led will flash alternately orange glow green with the last orange. (not to mistaken 4x because the printer will be totally dead, but it is temporary as well) Then ...
  6. Release both buttons simultaneously.
  7. Led will blink briefly and then will glow GREEN.
  8. And the computer will detect new hardware, just ignore ...
  9. Press the POWER button, then the printer will off.
  10. Press the POWER button again then the printer will on and ... PRINTER iP2770 is ready to use.
Other way on How To Reset Canon iP2770 error 5200 :
  1. Turn the printer, and printer will look normal.
  2. Run the printer for printing a document or a print test, then the 5200 error will appear.
  3. Directly unplug the power cord without pressing on/off button
  4. Open it and slide it into the middle of its cartridges manually
  5. Unplug all cartridges and leave the lid open
  6. Turn on the printer, head carriage will move left and right because the lid is still open and will stop in the middle.
  7. Replace the cartridge, and close the right
  8. The printer will return to normal.
read more...

How To Fix Your Printer

 


If this is a new cartridge, open the front cover and remove all cartridges. Be sure the protective film has been removed from the cartridge prior to installation. Inspect the contacts on the new cartridge for damage. Replace the cartridges in the correct place, close the front cover and power the printer down and then up again.


Printer Cannot Be Installed

If you’re trying to install a printer and it will not install, be sure to check the Device Manager in the Control Panel for any Unknown Devices. Your printer will be come an Unknown Device if you plug the cable in before installing the driver software. Remove the Unknown Device and then unplug the USB cable. Next, install the software that came with the printer, and when finished, plug the USB cable back in.

Printer Streaks

If your printer is producing a streaked image, you will need to clean the printer heads. To do this, go to Printers in the Control Panel, then right click your Printer then select Properties. A menu with the various settings will appear. You need to select Clean Printer Cartridges. The printer will run in cleaning mode.

Printer Does Not Print Jobs

When you click Print and nothing happens, you may be sending jobs to a printer that is not connected to your computer. For example, if another printer was previously installed, and you install a new printer, the old printer might still be setup as the Default Printer. Go into the Control Panel, then Printers and make sure the new printer is set to Default.

Printer Jams Frequently

If your printer jams frequently, you may be loading too much paper. This can also occur if you’ve had jams in the past and have a piece of debris still stuck in the printer. Use a flashlight to examine the entire mechanism to ensure no paper is still inside. This can also happen if an internal gear is damaged. You will often notice one side being fed faster than the other. This could me the printer is physically damaged and needs to be replaced or repaired.
read more...

9 tips to fix the printer

 






This time I will give you an easy way to improve printer. These ways I got from my personal experience that has proven efficacious

Here I emphasize is the model of printer ink disposable catride (usually brand HP). Usually fast printer like this at all damaged in the use of its cartridges. Well I would love to know how to fix catride printer. Although it should catride when it runs out it should buy a new one. But if you can still be repaired why buy a new one

Well for 9 tips on fixing this printer please read my next article. Hopefully my writing is beneficial to the reading.

9 tips to improve your printer:

1. Refill, refill ink might try just running out and you do not fill it

2. Remove and clean all parts catride, maybe you just catride dirty and so catride not functioning properly

3. Wipe with a tissue, if the ink had filled out and not come out, then wipe it with a tissue on the bottom place out of ink until the ink out. If the ink was not even out then see how the next.


4. Use warm water, if catridenya ink stuck in spending (not out of ink during operation). Normally only dry because it has not been worn but still quite a lot of ink. Wipe the bottom catride with warm water

5. Use of alcohol, when the warm water fails

6. Wrap with tissue, are less successful if the first way (usually ink had run out and you forgot to fill it) after wrapped let stand for 1-2 days. Remember tissue must actually touch the bottom where the ink discharge.

7. Shake from top to bottom. If the way before too long, shake it a bit harder then see if it's out of ink, if it is clean with a tissue

8. Give the air pressure. If the way previously not been successful. Charging ink from the hole you just give us the air pressures are strong enough, you can blow it if you have a large air pressure: D

9.
Pray, is the most effective way after all a try.

Usually I do after trying it we must pray and wait a day, usually better

Well hopefully these nine helpful tips on fixing printers. Welcome to try it at home
read more...